XTC 2 Clip

[Cortana 84]

CODE: xtc2clip

 

Short Description.

XTC 2 Clip is a specialized device for servicing HTC phones. With XTC 2 Clip you can Network Unlock, Repair IMEI, Repair CID, S-OFF many types of HTC Models

 

 

 

 

 

 

 

 

 

 

 

XTC 2 Clip

 

XTC 2 Clip is a specialized device for servicing HTC phones. It consists of a main device with a flex having a microsd emulator on its end.

 

 

Main Functions

 

 

• Sim unlock or lock a phone to a specified network with your own unlock code
  
• Repair IMEI (IMEI 2 for dual sim phones)
  
• Repair CID (Country ID used for firmware region lock)
  
• Repair MEID (for CDMA area phones)
  
• Change security level (S-ON/S-OFF, allows you to run unsigned code, perform service actions, etc)
  
• Many other functions you may need time-to-time.
  

 

 

 

Supported Models

XTC 2 Clip is to support the whole range of HTC phones, however the features may differ from model to model. Below is the list of tested models as per 1 May 2015:

 

 

• HTC M9
  Butterfly
  Butterfly 2
  Desire 200
  Desire 300
  Desire 400 DualSim
  Desire 500 dualsim
  Desire 510
  Desire 526G+ dualsim
  Desire 600 dualsim
  Desire 601 Dualsim
  Desire 601 singlesim
  Desire 610 singlesim
  Desire 620 Dual
  Desire 700 Dual
  Desire 816 dual sim
  Desire 816 SingleSim
  Desire 816G
  Desire 820
  Desire 820 Dual sim 820u
  Desire 820 mini
  Desire 820s
  Desire 826w
  Desire C
  Desire Eye
  Desire SV
  Desire U dualsim
  Desire V
  Desire X
  Droid Verizon
  E8 SingleSim Sprint
  Nexus 9
  One
  One E8 dual
  One E8 M8Sx Red
  One J (KDDI Japan)
  One M7
  One M8 DualSim
  One M8 SingleSim
  One Max
  One Mini
  One Mini 2
  One Remix Verizon
  One S
  One SV
  One V
  One X
  One XL
  Rider 4G
  Sensation (Pyramid)
  Sensation XL (X315e)
  Vivid
  Legacy
  chacha
  vivo pvt
  saga
  bliss
  icon_g
  legend
  buzz
  vision
  ace pvt
  pico pvt
  pyramid pvt
  pyramid pg58130
  pyramid pg58100
  rider
  

 

 

How does it work?

In order to use its functions – you have to connect it to the SD card port of your phone. The SD port may be located on the left, right or rear (battery) part of your phone. If your phone has no SD port – you must use Y-cable.

 

Operation mode

There are 2 operation mode for XTC 2 Clip device:

 

direct – when the phone is in fastboot mode & connected to the PC, using the XTC 2 Clip software

offline – when using a SIM Lock menu of bootloader. To use the offline mode you must first save special service files on XTC 2 Clip device.

 

 

Direct mode

 

 

• To use direct mode:
  
• Insert XTC 2 Clip device into phone SD card slot, power on phone into bootloader mode using “vol-down + pwr” button. And select “FASTBOOT” option.
  
• Connect phone to your PC.
  
• Run the XTC 2 Clip software and select “Direct mode”.
  
• Choose the desired operation and press corresponding button.
  SIM LOCK FUNCTION IS NOT AVAILABLE IN DIRECT MODE! PLEASE USE OFFLINE MODE FOR SIM LOCK MANAGEMENT.
   
  Important
   
  IF YOU GET A ‘SD CARD NOT FOUND’ MESSAGE – IT MEANS THAT THE XTC 2 CLIP WAS CONNECTED AFTER PHONE WAS POWERED ON. IN THIS CASE PRESS THE ‘REBOOT BOOTLOADER’ BUTTON AND REPEAT THE DESIRED OPERATION.
   
  
  

 

 

Offline mode

 

 

• How to prepare service files on XTC 2 Clip device:
  
• Connect the XTC 2 Clip device to your PC using any compatible microsd card reader.
  
• The device will be detected as a flash/disk drive.
  
• Run the XTC 2 Clip software and select “SD editor” tab.
  
• If you have previously had your service files on your device, please press “Read from drive” button, otherwise you will lose all your existing files once used the “Save to drive”.
  
• Select the options you need and press “Save to drive”
  
• Insert XTC 2 Clip device into phone SD card slot, power on phone into bootloader mode using “vol-down + pwr” button and select “SIMLOCK” option.
   
  Important
   
  THE SIM LOCK SETTINGS ARE BOUND TO THE PHONE’S IMEI. IN OTHER WORDS, IF YOU NEED TO LOCK/UNLOCK A PHONE, YOU MUST ADD PHONE’S IMEI TO SPECIAL ‘CONFIG.DAT’ FILE USING THE ‘SD EDITOR’ TAB.
   
  OTHERWISE YOU WILL GET ‘IMEI CHECKING FAIL’ AND YOUR PHONE WILL NOT BE UNLOCKED/LOCKED! CID, IMEI, SECURITY FLAG SETTINGS ARE NOT BOUND, YOU CAN USE IT ON AS MANY PHONES AS YOU WISH WITHOUT HAVING TO CONNECT THE DEVICE TO PC EACH TIME.
   
  
  

 

 

Offline mode – manual files creation

It may happen that you need to create service files on a PC with no XTC 2 Clip software installed. In this case you can manually create the files for:

 

 

• IMEI repair – imei.txt
  
• Security level change – sf.txt
  
• CID change – cid.txt
  

 

Please note, that unlike mentioned files, SIM lock configuration ‘config.dat’ is a binary file, and you may need to use a hex editor to create it. Therefore it’s recommended that you use an XTC 2 Clip software to create/manage this file.

TO CREATE/MODIFY THE FILES YOU CAN USE SIMPLE ‘NOTEPAD’ SOFTWARE

 

 

IMEI file

To modify the phone’s IMEI you need to create a text file called ‘imei.txt’ in the root folder of a XTC 2 Clipdevice disk drive. Once created, put inside a 14 digits of a new IMEI, for example: 12345678901234

 

 

SF file

To modify the phone’s security level (S-ON/S-OFF) you need to create a text file called ‘sf.txt’ in the root folder of a XTC 2 Clip device disk drive. Once created, put inside a number that corresponds to the desire security level:

 

 

• 0 means security OFF (S-OFF)
  
• 1 means (S-ON level 1)
  
• 2 means (S-ON level 2)
  
• 3 means (S-ON level 3, highest)
  

 

 

CID file

To modify the phone’s CID you need to create a text file called ‘cid.txt’ in the root folder of a XTC 2 Clip device disk drive. Once created, put inside a 8 symbols of a new CID, for example: HTC__001

 

 

 

 

قیمیت: 80 یورو

[ehsan_zamani_68 37]

نسبت به قیمت و کارکرد خیلی عالیه

بیاد تو بازار یکی میخرم حتما