رفتن به مطلب
تالار جی اس ام دولوپرز
جستجو در
  • تنظیمات بیشتر ...
نمایش نتایجی که شامل ...
جستجو در ...

XTC 2 Clip


ارسال های توصیه شده

CODE: xtc2clip

 

192.jpg

Short Description.

XTC 2 Clip is a specialized device for servicing HTC phones. With XTC 2 Clip you can Network Unlock, Repair IMEI, Repair CID, S-OFF many types of HTC Models

 

 

 

 

 

 

 

 

 

 

 

XTC 2 Clip

 

XTC 2 Clip is a specialized device for servicing HTC phones. It consists of a main device with a flex having a microsd emulator on its end.

 

 

Main Functions

 

 

  • Sim unlock or lock a phone to a specified network with your own unlock code
  • Repair IMEI (IMEI 2 for dual sim phones)
  • Repair CID (Country ID used for firmware region lock)
  • Repair MEID (for CDMA area phones)
  • Change security level (S-ON/S-OFF, allows you to run unsigned code, perform service actions, etc)
  • Many other functions you may need time-to-time.

 

 

 

Supported Models

XTC 2 Clip is to support the whole range of HTC phones, however the features may differ from model to model. Below is the list of tested models as per 1 May 2015:

 

 

  • HTC M9
    Butterfly
    Butterfly 2
    Desire 200
    Desire 300
    Desire 400 DualSim
    Desire 500 dualsim
    Desire 510
    Desire 526G+ dualsim
    Desire 600 dualsim
    Desire 601 Dualsim
    Desire 601 singlesim
    Desire 610 singlesim
    Desire 620 Dual
    Desire 700 Dual
    Desire 816 dual sim
    Desire 816 SingleSim
    Desire 816G
    Desire 820
    Desire 820 Dual sim 820u
    Desire 820 mini
    Desire 820s
    Desire 826w
    Desire C
    Desire Eye
    Desire SV
    Desire U dualsim
    Desire V
    Desire X
    Droid Verizon
    E8 SingleSim Sprint
    Nexus 9
    One
    One E8 dual
    One E8 M8Sx Red
    One J (KDDI Japan)
    One M7
    One M8 DualSim
    One M8 SingleSim
    One Max
    One Mini
    One Mini 2
    One Remix Verizon
    One S
    One SV
    One V
    One X
    One XL
    Rider 4G
    Sensation (Pyramid)
    Sensation XL (X315e)
    Vivid
    Legacy
    chacha
    vivo pvt
    saga
    bliss
    icon_g
    legend
    buzz
    vision
    ace pvt
    pico pvt
    pyramid pvt
    pyramid pg58130
    pyramid pg58100
    rider

 

 

How does it work?

In order to use its functions – you have to connect it to the SD card port of your phone. The SD port may be located on the left, right or rear (battery) part of your phone. If your phone has no SD port – you must use Y-cable.

193.jpg

 

Operation mode

There are 2 operation mode for XTC 2 Clip device:

 

direct – when the phone is in fastboot mode & connected to the PC, using the XTC 2 Clip software

offline – when using a SIM Lock menu of bootloader. To use the offline mode you must first save special service files on XTC 2 Clip device.

 

 

Direct mode

 

 

  • To use direct mode:
  • Insert XTC 2 Clip device into phone SD card slot, power on phone into bootloader mode using “vol-down + pwr” button. And select “FASTBOOT” option.
  • Connect phone to your PC.
  • Run the XTC 2 Clip software and select “Direct mode”.
  • Choose the desired operation and press corresponding button.
    SIM LOCK FUNCTION IS NOT AVAILABLE IN DIRECT MODE! PLEASE USE OFFLINE MODE FOR SIM LOCK MANAGEMENT.
     
    Important
     
    IF YOU GET A ‘SD CARD NOT FOUND’ MESSAGE – IT MEANS THAT THE XTC 2 CLIP WAS CONNECTED AFTER PHONE WAS POWERED ON. IN THIS CASE PRESS THE ‘REBOOT BOOTLOADER’ BUTTON AND REPEAT THE DESIRED OPERATION.
     
    194.jpg

 

 

Offline mode

 

 

  • How to prepare service files on XTC 2 Clip device:
  • Connect the XTC 2 Clip device to your PC using any compatible microsd card reader.
  • The device will be detected as a flash/disk drive.
  • Run the XTC 2 Clip software and select “SD editor” tab.
  • If you have previously had your service files on your device, please press “Read from drive” button, otherwise you will lose all your existing files once used the “Save to drive”.
  • Select the options you need and press “Save to drive”
  • Insert XTC 2 Clip device into phone SD card slot, power on phone into bootloader mode using “vol-down + pwr” button and select “SIMLOCK” option.
     
    Important
     
    THE SIM LOCK SETTINGS ARE BOUND TO THE PHONE’S IMEI. IN OTHER WORDS, IF YOU NEED TO LOCK/UNLOCK A PHONE, YOU MUST ADD PHONE’S IMEI TO SPECIAL ‘CONFIG.DAT’ FILE USING THE ‘SD EDITOR’ TAB.
     
    OTHERWISE YOU WILL GET ‘IMEI CHECKING FAIL’ AND YOUR PHONE WILL NOT BE UNLOCKED/LOCKED! CID, IMEI, SECURITY FLAG SETTINGS ARE NOT BOUND, YOU CAN USE IT ON AS MANY PHONES AS YOU WISH WITHOUT HAVING TO CONNECT THE DEVICE TO PC EACH TIME.
     
    195.jpg

 

 

Offline mode – manual files creation

It may happen that you need to create service files on a PC with no XTC 2 Clip software installed. In this case you can manually create the files for:

 

 

  • IMEI repair – imei.txt
  • Security level change – sf.txt
  • CID change – cid.txt

 

Please note, that unlike mentioned files, SIM lock configuration ‘config.dat’ is a binary file, and you may need to use a hex editor to create it. Therefore it’s recommended that you use an XTC 2 Clip software to create/manage this file.

TO CREATE/MODIFY THE FILES YOU CAN USE SIMPLE ‘NOTEPAD’ SOFTWARE

 

 

IMEI file

To modify the phone’s IMEI you need to create a text file called ‘imei.txt’ in the root folder of a XTC 2 Clipdevice disk drive. Once created, put inside a 14 digits of a new IMEI, for example: 12345678901234

 

 

SF file

To modify the phone’s security level (S-ON/S-OFF) you need to create a text file called ‘sf.txt’ in the root folder of a XTC 2 Clip device disk drive. Once created, put inside a number that corresponds to the desire security level:

 

 

  • 0 means security OFF (S-OFF)
  • 1 means (S-ON level 1)
  • 2 means (S-ON level 2)
  • 3 means (S-ON level 3, highest)

 

 

CID file

To modify the phone’s CID you need to create a text file called ‘cid.txt’ in the root folder of a XTC 2 Clip device disk drive. Once created, put inside a 8 symbols of a new CID, for example: HTC__001

 

 

 

 

قیمیت: 80 یورو

لینک ارسال

به گفتگو بپیوندید

هم اکنون می توانید مطلب خود را ارسال نمایید و بعداً ثبت نام کنید. اگر حساب کاربری دارید، برای ارسال با حساب کاربری خود اکنون وارد شوید .

مهمان
ارسال پاسخ به این موضوع ...

×   شما در حال چسباندن محتوایی با قالب بندی هستید.   حذف قالب بندی

  تنها استفاده از 75 اموجی مجاز می باشد.

×   لینک شما به صورت اتوماتیک جای گذاری شد.   نمایش به صورت لینک

×   محتوای قبلی شما بازگردانی شد.   پاک کردن محتوای ویرایشگر

×   شما مستقیما نمی توانید تصویر خود را قرار دهید. یا آن را اینجا بارگذاری کنید یا از یک URL قرار دهید.

×
×
  • اضافه کردن...