تمامی اپدیت های Z3X EasyJtag در این تاپیک

[Cortana 84]

Easy-JTAG Very HOT Update. v1.9.0.5 - FIRST IN THE WORLD!

 

NO ANY ADDITION ACTIVATION, NO ANY ADAPTERS.

LIKE USUALLY all hotest solution come free for all z3x users

 

After 6month of playing with EMMC we have new solution for you:

 

- KMVTU000LM-B503 [VTU00M] REPAIR

- READY CONDITION TIMEOUT ERROR REPAIR

- OCR READY TIMEOUT [EMMC BAD] REPAIR

- TOTALLY DEAD 00FF8080 REPAIR

 

This solution can repair 90% dead KMVTU000LM-B503 eMMC.

 

For work with solution you just need connect 1 MAGIC Z3X-TP for force EMMC firmware emmc mode.

 

Testpoin Location:

 

Here is Repair Manual:

 

1. Download latest Easy-Jtag install

2. Identify eMMC:

LOG:

OCR READY TIMEOUT [EMMC BAD]

Done.

3. Disconnect eMMC from power lines and easy-jtag box connector

(disconnect eMMCfrom box is important, because some voltage leakage via CMD, CLK, DAT0)

4. Make short testpoint [TP] to [GND] (solder small wire)

5. Plug eMMC power and connect Easy-Jtag box connector

6. Remove short [TP] to [GND]

7. Identify eMMC

LOG:

EMMC Date: 05/2005 Rev.0x56

EMMC NAME: 000000, S/N: 537986854

8. Start cUSTOM oPERATION ->'SAMSUNG: eMMC Update Firmware'

9. Confirm eMMC Part Numbet 'KMVTU000LM-B503'

 

 

LOG:

Z3X EasyJtag Software ver. 1.9.0.5

Loading eMMC Addon Firmware... IO: 2800 mV

Box S/N: XXXXXXXXXXXXXXXX, ,FW Ver.: 01.52

CMD Pullup Level:2052 mV

CMD Active Level:2588 mV

Setup firmware normal update mode, wait 2..30 sec...

Success!

Sending eMMC firmware...

Success!

Verifying eMMC firmware...

Success!

Flashing eMMC firmware...

Success!

Repairing eMMC CID...

Success!

eMMC firmware is updated now!

Please reconnect eMMC power lines before next operation!

Please don't forget to repair extCSDfrom backup!

Please don't forget to configure BOOTsizes!

Done.

 

Now eMMC is alive !!! Enjoy!!!

[Cortana 84]

Z3X Easy-JTAG Very HOT Update. v1.9.1.0 are out! Really Breaking news inside!

Easy-JTAG Very HOT Update. v1.9.1.0 Lot of changes:

 

Improved Samsung eMMC firmware update protocol

Added Samsung eMMC firmwares for new and old eMMCs ( FIRST IN THE WORLD) :

 

SAMSUNG KMVYL000LM-B503 [VYL00M] REPAIR (NAME 000000, OCR READY TIMEOUT ERROR [EMMC DEAD])

eMMC Repair FIRMWARE Samsung KMSJS000KA-B308 [sJS00A]

eMMC Repair FIRMWARE Samsung KMV3U000LM-B304 [V3U00M]

eMMC Repair FIRMWARE Samsung KLM8G2FB3B-D001 [M8G2FB]

 

 

 

 

 

Added NEW eMMC TP pinouts (Look inside sw folder: /EMMC TP PINOUTS)

 

 

Added via JTAG:

 

GSMART G1362 (Read/Write/Pinouts/Dump/RCP) FIRST IN THE WORLD!

 

 

Added via eMMC DIRECT(ISP)

 

Samsung GT-I9060(Read/Write/Pinout/Dump)

LG P715(Read/Write/Pinout/Dump)

 

 

 

Discussion thread

 

P.S. KMVYL000LM Repair solution are waiting for Smart Copy'n'Pasters.

P.P.S This solution are made in one day and free as every Z3X Update last 10 years.

Report Post Reply With Quote

[Pejvak 58]

EasyJTAG Box Addon Aka Android eMMC Explorer [Forensic Tool]

 

100% FREE for every EasyJTAG customer

No need to buy any volcanic stones

 

What is Android Explorer ?

 

Android Explorer are tool for browsing Android filesystem (EXT4) from eMMC Dump

or from directly connected eMMC Card or phone PCB!

 

What a general usage of this tool ?

 

Android Explorer allow you to extract some imortant data without dumping full image

like a user photos or contacts2.db file. You can extract any other important data

or simple explore android filesystem structure.

 

Why we need that - we have Ubuntu and VMware or MOORC adapter ?

 

If you have enough free time to do read 8/16/32/64Gb from eMMC - you can waste it.

 

How I can get it ?

 

Just Download EasyJTAG Installer 2.0.0.0 or newer.

 

 

 

 

Suppoted functions:

 

ISP connection or full dump browsing

Support EXT2 , EXT3 , EXT4

Extraction single files or group of files

Support GPT disk partitioning ( Samsung Method)

Support MBR disk partitioning ( HTC Method)

 

 

 

 

In next updates:

 

Support of NVIDIA / TEGRA / Mediatek partitioning.

Encryption and ACL support for EXT4.

Direct Export Contacts all logs etc in CSV,XLS file.

Recovery Deleted / Corrupted data from EXt4 Journal.

 

 

 

Video video

 

 

 

Discuss here

[MR.Ali 49]

EasyJtag Update v2.0.2.0 Released. Lot of new inside.

 

Added via JTAG:

 

- PRESTIGIO PAP5300 (Read/Write/JTAG_PINOUT/Dump/one click repair)

 

 

Adde via Direct EMMC(ISP)

 

- ALCATEL ONE TOUCH (IDOL) 6030X (Read/ Write/ EMMC_direct_pinout/Dump)

- SAMSUNG GT-I9158 (Read/ Write/ EMMC_direct_pinout/Dump)

- SAMSUNG GT-S7568 (Read/ Write/ EMMC_direct_pinout/Dump)

- HUAWEI MEADIAPAD 7 (Read/ Write/ EMMC_direct_pinout)

- ASUS ZENFONE 6 (Read/ Write/ EMMC_direct_pinout)

- ACER A200(Read/ Write/ EMMC_direct_pinout)

- LG G3 F460(Read/ Write/ EMMC_direct_pinout)

 

 

SD Unbrick CARD repaid new ZBIN:

- GT-I9506_I9506XXUAMHD_GPT_UEFI_4.2.2.zbin

- GT-I9295_I9295XXUBML3_GPT_UEFI_4.2.2.zbin

- GT-I9295_I9295XXUCNF1_GPT_UEFI_4.4.2.zbin

 

 

 

EMMC FIRMWARE UPDATE:

 

New FIRMWAREs:

KMV3W000LM-B310 [V3W00M] (VMX0 CONTROLLER)

KMS5X000KM-B313 [s5XKMB] (VPX0 CONTROLLER)

KLMAG2GE4A-A001 [MAG2GA]

 

 

NEW EMMC TP PINOUTS uploaded to support :

 

eMMC_TP_TYPE_5.jpg

eMMC_TP_TYPE_6.jpg

eMMC_TP_TYPE_7.jpg

eMMC_TP_TYPE_8.jpg

 

 

If need add something just goto -here

[MR.Ali 49]

EasyJtag_Release_v2.0.4.0 New phones

 

Added via JTAG:

- support LG E411G (Read/Write/JTAG_pinout/Dump/oneclickrepair)

 

Added via ISP(EMMC_DIRECT):

- support SAMSUNG SM-G313HZ (Read/Write/EMMC_ISP_pinout/Dump)

- support SAMSUNG SM-G386F (Read/Write/EMMC_ISP_pinout/Dump)

- support SAMSUNG GT-B5330L (Read/Write/EMMC_ISP_pinout/Dump)

- support LENOVO K910 (Read/Write/EMMC_ISP_pinout/Dump)

- support LG VS930 (Read/Write/Dump)

- support SAMSUNG SHV-E250K (Read/Write/EMMC_ISP_pinout)

 

Added via SD CARD REPAIR:

- SAMSUNG SM-G530FZ_G530FZXXU1AOF1_GPT_UEFI_4.4.4.zbin

- SAMSUNG SM-G530M_G530MUBU1AOA1_GPT_UEFI_4.4.4.zbin

[mobiledaneshjoo 16]

EasyJtag v2.0.8.1 Others Promise, We Do!

 

EasyJtag v2.0.8.1 Released

 

 

- Added option for shutting down PC after long operations.

- Added option for skipping unreadable blocks.

- Fixed *.binn file extension bug for auto resized files.

 

 

 

Added new phones via direct EMMC:

 

LG D500 (ISP Pinout,Dumps Added)

LG E440 (ISP Pinout,Dumps Added)

LG E445 (ISP Pinout,Dumps Added)

LG E730 (ISP Pinout,Dumps Added)

LG E960( ISP Pinout,Dumps Updated)

LG E975 (ISP Pinout,Dumps Added)

LG P990 (ISP Pinout Added)

LG P769 (ISP Pinout Added)

LG P713 (ISP Pinout Added)

LG P970 (ISP Pinout Added)

LG V410 (ISP Pinout Added)

LG F240S (ISP Pinout Added)

SAMSUNG SM-G350L (ISP Pinout,Dumps Added)

SAMSUNG SM-G357M (ISP Pinout,Dumps Added)

SAMSUNG SM-G530M (ISP Pinout,Dumps Added)

MEIZU M1 (ISP Pinout,Dumps Added)

 

THANKS to Seba Kopp , Legas , and others...

[mobiledaneshjoo 16]

EasyJTAG v.2.1 Released. New phones added and lot of changes.

Easy JTAG Software v.2.1 Release Notes:

We working hard last 3 years to make EasyJTAG are best solution on market.

We have greatly increased read and write operation speed , using a protocol compression.

In fact most dumps have areas with big amounts of repeating data. So what we get:

 

Test Config #1 Intel Core I5/8Gb , Windows 7 x64 eMMC Toshiba MMC16G

Write on FW1.52 976KB/S FW1.54 1449KB/S (48% speed increase)

Read on FW.52 788KB/S FW1.54 1457KB/S (84% speed increase)

 

Test Config #2 Intel Core 2Duo/2Gb , Windows XP x32 eMMC Toshiba MMC16G

Write on FW1.52 741KB/S FW1.54 1102KB/S (48% speed increase)

Read on FW1.52 606KB/S FW1.54 1074KB/S (77% speed increase)

 

 

Software changes:

- Added ability to configure eMMC bus frequency ( 1MHz,3MHz,7MHz,14MHz,21MHz)

- Fixed new Gemalto IDCore 10 security cards loss bugs. Link: Connection to protection card lost problem

- Improved software startup time.

- Improved eMMC operations speed.

- Fixed crash after updating box firmware.

 

 

Box Firmware 1.54 changes:

- Added eMMC read / write compression ( upto 1.4MB/s on typical eMMC data)

- Increased maximum clock rate for eMMC - 21MHz

- Improved box stability issues.

- Fixed SmartCard Detection Delay for Windows 7

 

 

 

New phones added via DIRECT EMMC(ISP) connection :

- support LG D295 (ISP Pinout, Dumps)

- support SAMSUNG SM-G130M (ISP Pinout, Dumps)

- support SAMSUNG SM-A500 (ISP Pinout, Dumps)

- support SAMSUNG GT-S7560M (ISP Pinout, Dumps)

- support SAMSUNG GT-S6790L(ISP Pinout, Dumps)

- support HUAWEI G510 (ISP Pinout, Dumps)

- support AMAZON KINDLE FIRE HD X43Z60 (ISP Pinout, Dumps)

- support SONY C2104 (ISP Pinout, Dumps)

- support SONY M2 (ISP Pinout, Dumps)

- support SONY C2005 (ISP Pinout)

 

 

Thanks all testers for great work!

Special thank to Seba Kopp and GsmServer crew for IDCore Samples!

For avoiding problems with X64 and drivers - use test signing mode

[MR.Ali 49]

EasyJtag Release v2.1.1.1

 

Added:

- additional AES 128 Security level * ( surprise for some copypasters )

Fixed:

- Z3X LG Tool (activated on EasyJtag) force close bug when select model

 

We are implementing new protection levels of our software to ensure our customers

to use authentic and well protected solution on market.

 

Added phones:

 

- support SAMSUNG SM-J200F (ISP Pinout, Dumps) [Thanks naushad09]

- support LG D405 (ISP Pinout, Dumps)

- support LG D410 (ISP Pinout, Dumps)

- support LG D415 (ISP Pinout)

- support LENOVO A1000 (ISP Pinout, Dumps)

- support LENOVO A706 (ISP Pinout, Dumps)

- support LENOVO P780 (ISP Pinout, Dumps)

- support LENOVO A390 (ISP Pinout, Dumps)

- support LENOVO A560 (ISP Pinout)

- support LENOVO A586 (ISP Pinout)

- support ACER Z130 (ISP Pinout)

 

Fixed some UI bugs.

Box Firmware 1.55

 

@customers - never eat spoiled seafoods ;-)

[mobiledaneshjoo 16]

EasyJtag Release v2.2.0.1. Very big Update. Lot of phones and changes!!!

EasyJtag Release v2.2.0.1. Very big Update. Lot of phones and changes!!!

- Added CMD42 Set MMC Password functionality for SD/eMMC. User can set and lock the User Area Partition

- Added Erase MMC Password to force erase Locked User Area Partition and reset device lock/unlock password

Screenshot:

- Improved/fixed software Region options to write selected regions into eMMC

- Added send crash report option to help Easy-Jtag team improve software

 

Added via ISP( direct EMMC) :

 

- support LG D280N (ISP Pinout, Dumps)

- support LG D285 (ISP Pinout, Dumps)

- support LG D320N (ISP Pinout, Dumps)

- support LG D325 (ISP Pinout, Dumps)

- support LG LS885 (ISP Pinout, Dumps)

- support LG LS991 (ISP Pinout, Dumps)

- support LG D605 (ISP Pinout, Dumps)

- support LG D625 (ISP Pinout, Dumps)

- support LG D631 (ISP Pinout, Dumps)

- support LG D821 (ISP Pinout, Dumps)

- support LG E980 (ISP Pinout, Dumps)

- support LG F100S (ISP Pinout, Dumps)

- support LG H345 (ISP Pinout, Dumps)

- support LG H443 (ISP Pinout, Dumps)

- support LG H525N (ISP Pinout, Dumps)

- support LG H631 (ISP Pinout, Dumps)

- support LG H635 (ISP Pinout, Dumps)

- support LG H811 (ISP Pinout, Dumps)

- support LG H815 (ISP Pinout, Dumps)

- support LG D160 (ISP Pinout)

- support LG H818P (ISP Pinout)

- support LG LS660 (ISP Pinout)

- support LG D838 (ISP Pinout)

- support LG D335 (ISP Pinout)

- support LG H618 (ISP Pinout)

- support SAMSUNG SM-A300 (ISP Pinout, Dumps)

- support SAMSUNG SM-G355M (ISP Pinout, Dumps)

- support SAMSUNG SM-G360M (ISP Pinout, Dumps)

- support SAMSUNG SCH-I545 (ISP Pinout)

- support SAMSUNG SGH-I747 (ISP Pinout)

- support SAMSUNG GT-I9506 (ISP Pinout)

- support SAMSUNG GT-S7275 (ISP Pinout)

- support МOTOROLA MOTO XT1022 (ISP Pinout, Dumps)

Report Post Reply With Quote

[mohsinsomeone 23]

EasyJtag Release v2.2.0.1. Very big Update. Lot of phones and changes!!!

 

Software changes:

 

- Added EasySupporter to help easy search and download support files without shell

Screenshot:

- Added CMD42 Set MMC Password functionality for SD/eMMC. User can set and lock the User Area Partition

- Added Erase MMC Password to force erase Locked User Area Partition and reset device lock/unlock password

Screenshot:

- Improved/fixed software Region options to write selected regions into eMMC

- Added send crash report option to help Easy-Jtag team improve software

 

Added via ISP( direct EMMC) :

 

- support LG D280N (ISP Pinout, Dumps)

- support LG D285 (ISP Pinout, Dumps)

- support LG D320N (ISP Pinout, Dumps)

- support LG D325 (ISP Pinout, Dumps)

- support LG LS885 (ISP Pinout, Dumps)

- support LG LS991 (ISP Pinout, Dumps)

- support LG D605 (ISP Pinout, Dumps)

- support LG D625 (ISP Pinout, Dumps)

- support LG D631 (ISP Pinout, Dumps)

- support LG D821 (ISP Pinout, Dumps)

- support LG E980 (ISP Pinout, Dumps)

- support LG F100S (ISP Pinout, Dumps)

- support LG H345 (ISP Pinout, Dumps)

- support LG H443 (ISP Pinout, Dumps)

- support LG H525N (ISP Pinout, Dumps)

- support LG H631 (ISP Pinout, Dumps)

- support LG H635 (ISP Pinout, Dumps)

- support LG H811 (ISP Pinout, Dumps)

- support LG H815 (ISP Pinout, Dumps)

- support LG D160 (ISP Pinout)

- support LG H818P (ISP Pinout)

- support LG LS660 (ISP Pinout)

- support LG D838 (ISP Pinout)

- support LG D335 (ISP Pinout)

- support LG H618 (ISP Pinout)

- support SAMSUNG SM-A300 (ISP Pinout, Dumps)

- support SAMSUNG SM-G355M (ISP Pinout, Dumps)

- support SAMSUNG SM-G360M (ISP Pinout, Dumps)

- support SAMSUNG SCH-I545 (ISP Pinout)

- support SAMSUNG SGH-I747 (ISP Pinout)

- support SAMSUNG GT-I9506 (ISP Pinout)

- support SAMSUNG GT-S7275 (ISP Pinout)

- support МOTOROLA MOTO XT1022 (ISP Pinout, Dumps)